Airlink101 AWLL7025 Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Airlink101 AWLL7025. Airlink101 AWLL7025 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 36
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Dual Band Wireless N USB Adapter
Model # AWLL7025
User’s Manual
Rev. 1.0
Zobrazit stránku 0
1 2 3 4 5 6 ... 35 36

Shrnutí obsahu

Strany 1 - User’s Manual

Dual Band Wireless N USB Adapter Model # AWLL7025 User’s Manual Rev. 1.0

Strany 2 - Table of Contents

10 Step 4 Verify that the Authentication Mode and Input Method match to your wireless router’s settings and click Next. Step 5 Input the encryptio

Strany 3 - 1. Introduction

11 Step 6 Keep the default IP Setting and click Complete. Step 7 You should see a blue circle around the antenna icon indicating a valid connection

Strany 4

12 Step 8 Go to the Link Information tab and click on the More button. Step 9 Verify that you are receiving adequate Signal Strength and Link Quali

Strany 5

13 If you do not have adequate Signal Strength, try re-orienting the Access Point and/or the USB Adapter by using the USB Extension Cable included in

Strany 6

14 4. Use Wireless Monitor Utility This section describes the various functions of the Wireless Monitor Utility that you can configure, including the

Strany 7 - 3. Configure the Adapter

15 The Wireless Information displays the current wireless network you are connected to as well as various other statuses such as the Signal Strengt

Strany 8

16 4.2 AP List The AP List tab displays all the available wireless networks detected by the USB Adapter. Simply select the desired wireless network y

Strany 9

17 4.3 Configure Encryption Settings This section describes how to configure encryption settings for the Dual Band Wireless N USB adapter. Note: The

Strany 10

18 Step 2 Verify the Profile Name is correct and click Next. Step 3 Verify the Network Name (SSID) is correct and click Next.

Strany 11

19 For WEP Settings: WEP Step 4.1 Select the appropriate Authentication Mode and Encryption settings and click Next. WEP Step 4.2 Enter the appro

Strany 12

2 Table of Contents 1. Introduction ...

Strany 13

20 For WPA-PSK and WPA2-PSK Settings: WPA Step 4.1 Select WPA-PSK or WPA2-PSK and the appropriate Input Method and click Next. WPA Step 4.2 Enter

Strany 14 - 4.1 Link Information

21 Step 5 Keep the default IP Setting and click Complete to finish the settings. Step 6 You should see a blue circle around the antenna icon indica

Strany 15

22 4.4 Profile Setting The Profile Setting tab lists all the profiles you have created. You can create new profiles for different network environment

Strany 16 - 4.2 AP List

23 Step 3 Enter the SSID (Network Name) of the wireless network you want to connect to and click Next. Step 4 Configure any encryption setting if r

Strany 17

24 Step 5 Keep the default IP Setting and click Complete to finish the profile setting. Step 6 Your new profile will be listed in the Profile List.

Strany 18

25 4.5 Configure IP Setting To change the IP settings of the wireless adapter, follow the steps below: Step 1 On the last step of 4.4 Profile Settin

Strany 19

26 4.6 WiFi Protected Setup (WPS) Airlink101 Dual Band Wireless N USB Adapter has an innovated built-in WPS (WiFi-Protected Setup) feature which can

Strany 20

27 Step 3 The Router will now start the handshake with the wireless adapter. When you see the window below, the wireless connection has been establis

Strany 21

28 Step 2 Click on Rescan button. The wireless router or AP you wish to connect to should appear in the list. Write down the PIN code on a piece of pa

Strany 22 - 4.4 Profile Setting

29 The router will start to search for the WPS enabled device with matching PIN code. Step 5 Select the Router/AP you want to connect to and click

Strany 23

3 1. Introduction Thank you for purchasing Airlink101 Dual Band Wireless N USB Adapter. The AWLL7025 Dual Band Wireless N USB Adapter can operate on

Strany 24

30 4.7 About The About tab shows the Utility, Driver, and Firmware version as well as the MAC address of the Dual Band Wireless N USB Adapter.

Strany 25 - 4.5 Configure IP Setting

31 Appendix A – Specifications Standards • IEEE 802.11n draft 2.0 • IEEE 802.11 a / b / g Frequency Ban

Strany 26

32 Appendix B – Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limit

Strany 27

33 This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause

Strany 28

34 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part

Strany 29

35 [French] exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del cos

Strany 30 - 4.7 About

36 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theoreti

Strany 31 - Appendix A – Specifications

4 2. Install Utility and Driver This Quick Installation Guide only provides the basic installation instructions. For detailed installation instructio

Strany 32 - Appendix B – Information

5 Note: If the Autorun screen doesn’t appear automatically go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) an

Strany 33

6 Step 5 Click Next to begin the installation. Step 6 Give Permission to Window to install the driver software For Windows Vista, click the Instal

Strany 34

7 3. Configure the Adapter This section describes how to connect your Dual Band Wireless N USB Adapter to a wireless network. Note to Windows XP Use

Strany 35

8 Open the Airlink101 Wireless Monitor utility by double clicking on the Airlink101 Wireless Monitor Utility icon in the system tray at the bottom ri

Strany 36 - Technical Support

9 Step 2 If encryption is not enabled for the selected access point / router, skip to step 7. Otherwise, enter a Profile Name for your wireless settin

Komentáře k této Příručce

Žádné komentáře